Introduction to shower installation considerations, let's look at what shower accessories. We know that the main parts a frame, glass,retaining bar, smoke doors, wheels, handles, shower and other main parts, other gadgets are also bathroom clip, jacking yards, sandwiched, hinge, rod, shaft ,shower room lock, glass clip, plastic parts and other small items. Selected asthe main condition to secure, ...

Generally, if samples, by air or by express(DHL,UPS,FEDEX,TNT,EMS......)If bigger order, by sea or by train are all available.

We are a manufactory&trading company.

Yes, it is easy to print your logo on the packing

Yes, generally, free sample for 1~2pcs, and the freigt you need to bear.

ShangHai/NingBo/GuangZhou/ShenZhen/Tianjin Port

In standard export cartons, but could be designed as your request.

We have CE, UL,ROHS,CSA,CUPC certificate.

we offer EXW;FOB;CNF and CIF, we have a long-termed cooperated forwarder for sharing the service for both of us.

Therecould be an air leak on the suction side of the pump.Checkto make sure the suction line is free of obstructions.Checkto make sure the impeller is still attached to the shaft of the motor. If theimpeller has broken off, it will need to be replaced.If thepump is installed at a distance from the pool or is elevated above the normaldeck level, the time needed to prime the pump could be longer. ...

Waterway pumps/motors are factory wired for 240 volts ONLY,unless the motor is 120 volts. Check the voltage of the incoming supply powerand ensure the motor is wired or can be wired for this voltage (data plate onmotor will help provide voltage and wiring information). Also check for looseor badly connected wires. Contacta certified electrician for repair.

Themotor has an internal cooling fan that can be heard. When installing your pump,it is advised to carefully consider the location; under a bedroom window maynot be an ideal location.Vibrationfrom the pump’s feet and the base (where the pump rests) can cause the pump tobe noisy. A piece of old carpet or rubber between the pump’s base and equipmentpad might reduce the noise.Ensurethe pump is level ...

Thismay be caused by insufficient power due to an undersized wire or a poorconnection. The pump must be wired according to the wiring diagram locatedon the motor label. Consult a professional electrician. Yourlocal power company might be experiencing a power drop especially during a heatwave. Restart your pump when the weather cools to confirm that the problem isreally in the motor.Yourpump may ha...

It isvery important that your pump is located in an area that has adequate drainageto prevent floodingfrom rain and other water sources. Check to make sure thepump did not fail because of water damage. Check the power (a volt meter isneeded to check voltage), breakers, switches, etc., to ensure your pump iselectrically powered. Determining the voltage is very important.Thepump must be wired accord...

With an air push button the solutions arequite simple most of the time. 1. If the button is hard to press or comesback too slowly to its initial position, there may be too much air accumulatedwithin the hose. - To correct the problem, locate thetransparent hose and with a thin pin, poke one or two holes through it to letthe air out. (This will not harm your system in any way).- Verify that the hos...

Toverify that the air-heating element is functioning normally, turn on yoursystem and let it run. After approximately 5 minutes, touch the air hose thatis connected to your blower. It should feel hot. 1. Ifthe hose does not feel hot, contact your distributor who will guide you throughthe procedure to get your blower changed. 2. Ifthe air hose feels hot, the blower is not defective. The cool sensat...

Checkthe HP of the motor for GPM. Determine how many jets are in the spa. You shouldhave 10-12 GPM per jet.Checkretainer ring for the following:1. Retainer ring does nothave Teflon tape around thread or not enough.2. Retainer ring is notthreaded in all the way. You may need to extend length with 1″ coupler.3. Retainer ring and 1″ pipeis not glued in all the way so that it is flush with...

Proway makes and uses onlyhigh quality steel molds which last longer and produce cleaner parts withbetter tolerances.

Most spa and bath parts arestocked in gray, black and white. Custom colors are available on special order.Minimum quantities may apply.

ABS, PVC, stainless steel,chrome brass.

Waterway pumps should never operate without water. The pump sealassembly in the pump volute (area between the strainer basket and the pumpmotor) protects the pump motor from pool water. This seal assembly gets hot andis cooled by the pool water. If the pump is running without water, the sealwill overheat and melt, if left running without water for a long period oftime, the heat generated could d...

Horsepower is matched with the impeller inside the pump.Havinga larger impeller on a smaller horsepower motor will cause premature failure ofthe motor. It is better to replace it with the same horsepower. You can onlydownsize the impeller in horsepower rating.

Thiscould be because the pump is a “flooded suction” and the water from the pool isdraining into the strainer basket, making lid replacement very difficult.Verify that the pump is off. The hose from the skimmer to the pump can have avalve installed to shut off the water or plug the skimmer until you can get thelid back on.With a flooded suction there should ideally be a valve at theskimmer and o...

--Small amount: western union, paypal--Big amount:T/T, D/P, L/C, O/A